METAL CUTTERS AND TRIMMERS
METAL CORNER ROUNDERS
Accucutter® is a US manufacturer of equipment used in the recognition and sign industries and for general lightweight metal fabrication. Its product line of shears and cornering systems is the largest offered by any company. All are original designs manufactured and assembled at its facilities in Carlisle, Pennsylvania. accucutter®,it's more than a name, it's your assurance you are buying the best.
In 2006 Accucutter® completely redesigned the Model 2001 12” Shear. The new design is the result of two years of systematically evaluating and field testing every component of the shear. The result of the development effort is a new shear that is lighter, more compact, more durable, and easier to use. At first glance it may look the same old shear, but the shear table is the only part that remains the same as the original 2001. It is the complete evolution of the 12” table shear and is named the 2001EVO. Listed below are just some of the features that make the 2001EVO unique.
Curved Power Blades
Size & Weight:
13" EVO 3001 Metal Cutter
3001 13" Sheer Cutter
19" EVO3001 Metal Cutte
r 25" EVO3001 Metal Cutter
The 3001 Guillotine Shear was originally designed in 1999. The original prototype was a 13" shear and continues in use in Accucutter's® shop. While the basic design of the 3001 shears has remained unchanged since that original prototype, the shears have continued to evolve with changes made as appropriate. Three 3001 shears are available; a lighter duty 13" and the standard 13" and 25".
The 3001EVO/13 is the lighter duty version of the original 13" shear and is discussed at the bottom of the page. The standard 13" and 25" shears (3001/13 & 3001/25) have been upgraded with 1/2" thick end plates, heavy duty alignment blocks for the upper blade holder with 1/4" thick aluminum bronze wear plates, and a new drop off/rear gauge. In addition, all of the shears have the Standard Features listed below.
The standard 13" & 25" shears are constructed to industrial standards, and the resulting mass of the shears contributes significantly to their performance. If you have worked with industrial equipment, you know that the heavier, sturdier equipment is more stable and less fatiguing to operate. Depending on the size, the shears weigh from 85 to 150 pounds. Most of the weight is in the guillotine action that is made entirely of steel. Once that mass is put in motion, its inertial contributes to the ease and smoothness of the operation of the shear. While lighter weight designs can move during use and be difficult to use, the standard 13" & 25" shears do not have these problems. The shears cut foils, aluminum and plastic with little or no effort. Even the most timid operator can cut harder materials like half-hard trophy brass producing full width cuts that are flat and square.
The 3001 shears were designed and developed by Accucutter® and are manufactured at its facility in Carlisle, Pennsylvania. They offer the extra precision and power of a larger commercial guillotine shear in a smaller, more affordable bench shear that provides convenience and flexibility unavailable in any other shear on the market.
* * * * *
Model 3001 Standard Features:
Accucutter®’s exclusive “Flip-Up Hold-Down” is standard on all standard 3001 shears. When in the down position, it automatically applies pressure to the material to facilitate smooth, accurate cutting. When necessary, the hold-down may be flipped up out of the way to permit easy access to the blades.
The shear handle may be installed on the left or right of the shear enabling right handed and left handed operators to use the same shear.
Precision Drop-Off Bar
The Precision Drop-Off Bar is full width and is an invaluable aid for making accurate, repetitive cuts. It is mounted to the top blade carrier and moves up and down with the top blade like the rear gauge on many larger guillotine shears. It is above the material and doesn't interfere with the material as it falls away from the shear after it is cut. It slides on two alignment rods and is locked in position by turning a knob on each rod.
The typical ruler is a stamped piece of thin metal. The ruler from Accucutter® is machined from a thick, solid piece of steel. There are six separate steps involved in its manufacture with the last being a precision grinding of the front edge to insure that the ruler is straight and true. Because of its thickness, it is very stable, and the edge will not lift or distort allowing material to slide underneath the ruler. Lastly, the ruler is stepped to place the measuring edge close to the work surface for easier reading. The ruler is graduated in 1/16th's of an inch.
The standard 3001 uses the same blade system pioneered by Accucutter® on its 2001 Bench Shear. The blades are mounted with tapped bolts rather than the old fashion nut and bolt system, and the bottom blade is adjusted with set screws instead of eccentrics. A much safer, quicker and simpler method of installing and adjusting the blades.
· Aluminum................................................. .040"
· Brass........................................................ .025"
· Flexible Plastic........................................... .125"
· Brass Plated Steel....................................... .025"
Size & Weight:
· 3001/13 - 26"L x 20"W x 12.5"H (W/out handle); Approximately 85 lbs.
· 3001/25 - 26"L x 32"W x 12.5"H (W/out handle); Approximately 150 lbs.
Availability & Ordering
The 3001 is built to order. Please check for current availability and delivery. At the time of ordering it is necessary to specify which type of blade you prefer. The choices are either for metal or, for plastic. The 13" is also available with a multi-purpose blade. If you are unsure which blade will be best for you, call Accucutter®to discuss your choice.
Corner Rounder, includes 1/4" and 3/8" die set, Cuts up to .080 aluminum, 1" Card Stock, Plastics, Magnetic Sheets and More....extra dies available
Model 9387 2" Super Punch
2" Disc Cutter for metal or plastic
Easy to use and portable. See what you punch, making it easy to align your material. Make efficient use of your engraving stock.
Punch out your own blanks as you need them, in the color and quantity you want.
Punch and die are hardened tool steel for many years of use.
Shear Capacity: · Aluminum.025" · Brass ..025" · Flexible Plastic .060" · Brass Plated Steel.020"
SEPS Graphics Offers Metal Cuuters, Metal Sheers, And Corner Punches for the Sign and the
Trophy and Sublimation Industry.
Sign Vinyls Supplies, adhesive Vinyls, Printable vinyls, sign vinyl tools, gromment machines, hard subtrate cutters, grommented vinyls, vinyl cutters, Wideformat Printers, Heat presses, blank mirror licence plates, masking supplies, glitter adhesive vinyls, t shirt equipment,
rhinestones equipment and much more.
We do not have all the items available on the web, but we can get them for you.
Please call or email us if you a something you need and want us to find.
Seps Graphics offers the best customer service around,monday thru friday 8-5 central time.
SEPS GRAPHICS INC. 103 Trade Center Drive Birmingham, Al 35244
1-800-886-3331 205-444-5554 fax 205-444-5545